If so, simply apply a small amount again over the hole and let it dry until the patch is even with the wall surface. After it has dried, the spackle may have depressed slightly below the surface of the wall. Let the patch dry completely – this usually takes a few hours. Do this quickly before the compound sets. Use a damp cloth to remove any compound adjacent to the patch that you didn’t remove by scraping. Take care that you don’t remove the spackle from the hole or crack when you remove the excess. Scrape away excess compound from the wall with your putty knife with the blade at a 90-degree angle to the wall. It dries quickly and can be ruined if left exposed to the air. You can also scrape excess compound from the narrow knife onto the edge of the wide knife for a cleaner, more controlled application.Īlways close the spackling compound lid after you’ve taken out what you need. The narrow knife can be used to apply the compound to the damaged area on the wall. Dip the wide knife into the can of spackling compound and use it as a palette. Helpful TipsĬonsider using two putty knives - one with a wide blade and one with a narrow blade. Do this until the hole is completely filled in. Put the compound-covered blade of the putty knife at a 45-degree angle to the wall and spread the compound over the hole or crack in a smooth, feathering motion. You won’t be slathering the compound on the damaged area, so you want just enough of it to fill in the hole or crack. Open the container of premixed spackling compound and scoop up a small amount of it with the edge of a putty knife. See Patch and Repaint Walls.Īfter you have scraped or sanded the area, wipe it down with a damp cloth to remove any dust and residue. If you’re working on holes of 2" or greater in diameter, you may need to purchase or make a wall-repair patch and apply it before using joint compound to seal it in place. If you’re going to spackle over nails or screws that popped through your wall’s paint, use a nailset and hammer to push them in below the wall’s surface. Just give it a couple of quick brushes with the sandpaper to smooth it down. Helpful Tipsįine-grit sandpaper is good for smoothing down the surface around a hole if there are not too many fragments or a protruding outer edge. Press the putty knife firmly against the wall at an angle and scrape up and down until the dust and debris stops falling. You’ll undoubtedly remove some paint sitting right around the hole, but since you’ll be painting over the spackling compound once it’s dried, don’t sweat it. Be careful not to make the hole or crack bigger. Use a putty knife to gently scrape away loose paint and protruding fragments of wallboard until the surface around the hole is as smooth as the rest of the wall. You want the area directly around the hole to be as smooth and even as the rest of the wall’s surface. Often, a hole in drywall, whether it’s caused by blunt force or by a screw, nail or other type of fastener, will have an outer edge or fragments that protrude outward. Step 1: Prepare the Spackling Spotīefore applying spackle, you must clean and otherwise smooth out the area around the hole or crack so that the surface is optimized for proper spackling paste adhesion. It can be used like spackle, but it is better for repairing larger holes and damage that require backing or other reinforcement. Joint compound is mostly used to cover joints between wallboard panels and to cover the fasteners and screws used to attach wallboard to studs underneath. It is also sometimes used, erroneously, in reference to drywall joint compound, which is similar but an altogether different product. Actually, the word Spackle® itself is a registered trademark but it is commonly used to describe spackling compound. It comes in powdered (mixed with water before application) or paste form, the paste form being the most commonly used and known. Spackling paste or spackling compound is made of gypsum powder and binders and is used to patch small holes, cracks and other imperfections like dents in drywall, plaster walls, and sometimes in wood. Spackling Schoolīefore you start, here’s a brief lesson on spackle. Keep reading to learn proper spackling technique so that you know how to do it easily and correctly every time. Repairing holes and dings in walls with spackle and paint is one of the easiest home improvement projects you can undertake to vastly improve the look of your home’s interior.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |